 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER innovASIC Features * * * * * * * * * * * * Form, Fit and Function Compatible with the DECTM 21140AF Available in 144 Pin PQFP Package Integrated Ethernet controller with PCI bus interface Supports 10 Mb/s and 10/100 Mb/s network interface PCS and scrambler/descrambler circuitry on chip Supports multiple PCI features: - Unlimited PCI burst - PCI read multiple - PCI write and invalidate - PCI read line - PCI 5.0V and 3.3V environments Multiple interrupt sources Contains two independent 3K FIFOs to minimize external memory additions Provides sleep or snooze low-power modes Interfaces with MicroWireTM Serial ROM Provides a JTAG test port with boundary scan function Complies with IEEE 802.3, ANSI 8802-3, and Ethernet standards The IA21140AF is a "plug-and-play" drop-in replacement for the original IC. innovASIC produces replacement ICs using its MILESTM , or Managed IC Lifetime Extension System, cloning technology. This technology produces replacement ICs far more complex than "emulation" while ensuring they are compatible with the original IC. MILESTM captures the design of a clone so it can be produced even as silicon technology advances. MILESTM also verifies the clone against the original IC so that even the "undocumented features" are duplicated. This data sheet documents all necessary engineering information about the IA21140AF including functional and I/O descriptions, electrical characteristics, and applicable timing. Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 1 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Package Pinout int_n rst_n vdd vss pci_clk vdd gnt_n req_n vss ad[31] ad[30] vss ad[29] ad[28] vss ad[27] ad[26] vdd ad[25] ad[24] c_be_n[3] idsel vss ad[23] ad[22] ad[21] ad[20] vdd ad[19] ad[18] vdd vss vss ad[17] ad[16] vss 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 tdo tdi tms tck srl_txen srl_tclk srl_txd srl_rclk srl_rxen srl_rxd srl_clsn mii_srl sym_txd[4] mii_sym_txd[3] mii_sym_txd[2] vdd vss mii_sym_txd[1] mii_sym_txd[0] mii_sym_txen sym_link mii_sym_tclk rcv_match vdd vss sym_rxd[4] mii_sym_rxd[3] mii_sym_rxd[2] mii_sym_rxd[1] mii_sym_rxd[0] mii_sym_rclk mii_crs mii_clsn mii_dv mii_err sd 111111111111111111111111111111111111 444443333333333222222222211111111110 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 333444444444455555555556666666666777 789012345678901234567890123456789012 IA21140AF vss vdd mii_mdc mii_mdio nc br_a[1] br_a[0] br_ce_n br_ad[7] br_ad[6] vdd vss br_ad[5] br_ad[4] br_ad[3] br_ad[2] br_ad[1] br_ad[0] vss gep[7] gep[6] gep[5] gep[4] vdd vss gep[3] gep[2] gep[1] gep[0] sr_cs sr_ck sr_di sr_do vdd vss vdd_clamp Copyright (c) 2001 innovASIC The End of ObsolescenceTM vss c_be_n[2] frame_n irdy_n trdy_n devsel_n stop_n vdd perr_n serr_n par c_be_n[1] vss ad[15] ad[14] ad[13] vss ad[12] ad[11] vdd ad[10] ad[9] vss ad[8] c_be_n[0] ad[7] ad[6] vss ad[5] ad[4] vdd ad[3] ad[2] vss ad[1] ad[0] ENG210010110-00 www.innovasic.com Customer Support: 1-888-824-4184 Page 2 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Description The innovASIC IA21140AF Fast Ethernet LAN controller provides a direct interface connection to the PCI (Peripheral Component Interface) bus. It interfaces with the PCI bus by using on-chip control and status registers (CSR's), and a shared CPU memory area. The memory is initialized once during setup to minimize CPU overhead during normal operation. Large receive and transmit FIFO's are contained on-chip so no additional on board memory is required. The IA21140AF includes two on chip direct memory access (DMA) controllers with programmable burst size providing for low CPU utilization. A PCI clock frequency from dc to 33 MHz (20-33 MHz for operational network interface) is supported. Two network ports are supported. A serial standard 7wire 10-Mbps port (SRL) and a media independent interface/symbol 10/100-Mbps port (MII/SYM). The 10 Mbps implements a direct interface to the external 10 Mbps front-end decoder (ENDEC). The 10/100 Mbps port supports two modes. The first is a 100BASE-X physical coding sublayer (PCS). The second is a full implementation of the MII standard. The IA21140AF functions in a full-duplex environment for either network port. Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 3 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER System Block Diagram This block below illustrates the major functions of the IA21140AF. Boot ROM/ External Register Serial ROM Board Control Signals PCI PCI Interface 32 DMA 32 Rx FIFO 16 RxM 4 Boot ROM Port 32 Serial ROM Port 32 32 Tx FIFO 16 TxM GeneralPurpose Register 8 4 Physical Coding Sublayer 4 1 1 Scrambler/ Descrambler 4 Serial Interface MII/SYM Interface 10 Mb/s 10 Mb/s or 100 Mb/s Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 4 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER I/O Description The following section provides a functional description of the I/O pins on the IA21140AF. NAME Vdd Vdd_clamp Vss ad[31:0] br_a[1:0] br_ad[7:0] Type Description P 3.3 volt input supply voltage. P 5.0 volt reference for 5.0 volt signaling environments and 3.3 volt reference for 3.3 volt signaling environments. P Ground Pin I/O The PCI address and data lines are multiplexed on the same PCI pins. During the first clock cycle of a transaction, the 32 bits contain an address and during subsequent clock cycles, they contain data. Both read and write bursts are supported in master operation only. Big or Little Indian byte ordering can be used. O Address line bit 0 also carries in two consecutive address cycles (bits 16 and 17) in a 256KB configuration. Bit 1 also latches the boot ROM address and control lines via two external latches. I/O In the first of two consecutive address cycles, these multiplexed lines contain the boot ROM address bits [7:2], oe_n, and we_n. The second cycle contains boot ROM address bits [15:8]. Bits 7 through 0 contain data during the data cycle. These lines are used to carry data to and from the external register. O I/O Enable pin for the Boot ROM or an external register. Pin has an internal 5 k O pull-up resistor. Bus command and byte enable are multiplexed on the same PCI pins. These bits provide the bus command during the address phase of the transaction. They provide the byte enable during the data phase. Byte enable determines which byte lines carry valid data. Bit 0 coincides with byte 0. Bit 1 coincides with byte 1, etc. Indicates that the driving device has decoded its address as the target of the current access. As an input, determines whether a device on the bus has been selected. The IA21140AF bus master asserts this signal to indicate the beginning and duration of a bus transaction access. Data transfer continues while this signal is asserted. Deasserting this signal indicates the transaction is in the final phase. These pins can be configured by software to perform either input or output functions for system specific applications. Indicates to the IA21140AF that access to the bus has been granted. Used as a chip select by the host to indicate configuration read and write cycles. When one of the appropriate bits in CSR5 gets set, interrupt request gets asserted if the corresponding mask bit in CSR7 is not set. If more than one interrupt bit in CSR5 is set and all input bits are not cleared, interrupt request gets deasserted for one clock cycle. Interrupt request gets deasserted by writing a "1" into the appropriate CSR5 bit. This pin must be pulled up by an external resistor. br_ce_n c_be_n[3:0] devsel_n I/O frame_n I/O gep[7:0] gnt_n Idsel int_n I/O I I O/D Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 5 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER NAME irdy_n Type Description I/O When the IA21140AF is the bus master, this signal is asserted during write operations indicating valid data is present on the 32-bit ad bus. It is asserted during read operations to indicate the master is ready to accept data. It is asserted during a write to indicate that valid data is on the AD lines. A data phase is completed on any rising edge of the clock when both irdy_n and trdy_n are asserted. Wait cycles are inserted until both these signals are asserted together. I When an external physical layer protocol (PHY) device detects a collision, it asserts this signal. I The PHY sets this bit when the media is active. I An external PHY sets this bit when receive data is on the mii_sym_rxd lines and is cleared at the end of the packet. This signal is synchronized with mii_sym_rclk. When a data decoding error is detected by an external PHY device, this pin gets set. It is synchronized to mii_sym_rclk and can be set for a minimum of one receive clock. It sets the cyclic redundancy check (CRC) error bit in the receive descriptor (RDES0) when it is set during a packet reception. Goes to the PHY devices as timing reference for the transfer of information on the mii_mdio signal. Transfers control information and status between the IA21140AF and PHY. Set when the MII/SYM port is selected. Cleared when the SRL port is selected. This clock, recovered by the PHY, supports either the 25 MHz or 2.5 MHz receive clock. When MII mode is selected, these four parallel data lines receive data that is driven by external PHY that attached the media. Synchronized to the mii_sym_rclk signal. This 25 MHz or 2.5 MHz transmit clock is supplied by the external physical layer medium dependent device (PMD) and must always be active. These four parallel transmit data lines are synchronized and latched by the external PHY on the rising edge of the mii_sym_tclk signal. This signal indicates a transmit to an external PHY device. It reflects the transmit activity of the MAC sublayer when in the PCS mode (CSR6[23]). No connection pins Even parity bit for the 32-bit ad bus and the 4-bit c_be_n lines. It is driven by the master for address and write data phases and driven by the target for read data phases. Timing of the PCI related functions is based on this DC to 33 MHz clock. All bus signals except int_n and rst_n are sampled on the rising edge of this clock. Used for reporting data parity errors during all PCI transactions except a special cycle. Set when a received packet passes address recognition. Request to the bus arbiter for the IA21140AF to use the bus. When asserted for at least 10 PCI clock cycles, the IA21140AF is reset to its initial state. PCI output pins are tristated and all PCI O/D signals are left floating. Supplied by an external PMD device. mii_clsn Carrier sense mii_crs mii_dv mii_err I mii_mdc mii_mdio mii_srl mii_sym_rclk mii_sym_rxd[3:0] O I/O O I I mii_sym_tclk mii_sym_txd[3:0] mii_txen Nc Par I O O O I/O pci_clk I perr_n rcv_match req_n rst_n I/O O O I sd Copyright (c) 2001 I ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 6 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER NAME serr_n sr_ck sr_cs sr_di sr_do srl_clsn Type Description O/D Reports errors other than parity. Signal must be valid for at least one clock cycle. This pin pulled up by an external resistor. O Serial ROM clock. O Serial ROM chip-select pin pulled down by an internal 2 k O resistor. O Serial ROM data-in. I Serial ROM data-out pin pulled up by an internal 5 k O resistor. I Indicates a collision occurrence on the Ethernet cable to the IA21140AF. Asserted and deasserted asynchronously by the external ENDEC with respect to the receive clock. I Carries the recovered receive clock supplied by an external ENDEC. May be inactive during idle periods. I I Carries the input receive data from the external ENDEC. Incoming data should be synchronous with receive clock (srl_rclk) signal. Set when receive data is present on the Ethernet cable and cleared at the end of a frame. Set and cleared asynchronously to the receive clock by the external ENDEC. Carries the transmit clock supplied by an external ENDEC. Must be always active, even during reset. Carries the serial output data from the IA21140AF and is synchronized to transmit clock signal. Signals an external ENDEC that the IA21140AF transmit is in progress. The current target is requesting the bus master to stop the current transaction. Descrambler is locked to the input data signal. This signal and the four receive lines mii_sym_rxd[3:0], provide five parallel data lines in symbol form for use in PCS mode. Data is driven by an external PMD device and is synchronized with respect to the mii_sym_rclk signal. This signal and the four transmit lines mii_sym_txd[3:0], provide five parallel data lines in symbol form for use in PCS mode. Data is synchronized on the rising edge of mii_sym_tclk. During JTAG test operations this clock shifts state information and test data into and out of the IA21140AF. The pin should not be left unconnected. During JTAG test operations this pin serially shifts test data and instruction into the IA21140AF. The pin is pulled up by an internal 5 k O resistor and should not be left unconnected. During JTAG test operations this pin serially shifts test data and instructions out of the IA21140AF. Controls the state operation of JTAG testing in the IA21140AF. The pin is pulled up by an internal 5 k O resistor and should not be left unconnected. Indicates the readiness of the target's agent to complete the current data phase of the transaction. During reads, this signal indicates that valid data is present on AD lines. During writes, this signal indicates the target is ready to accept data. A data phase is completed on any clock when both irdy_n and trdy_n are set. srl_rclk srl_rxd srl_rxen srl_tclk srl_txd srl_txen stop_n sym_link sym_rxd[4] I O O I/O O I sym_txd[4] O tck Tdi I I tdo tms trdy_n O I I/O Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 7 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER AC/DC Parameters DC Characteristics Absolute Max Ratings Symbol VDD VDD TA TJ Parameter Supply voltage (3.3V) Supply Voltage (5V) Ambient Temperature (Commercial) Junction Temperature (Commercial) Storage Temperature Min 3 4.75 0 0 -55 Max 3.6 5.25 70 85 125 Unit V V C C C CMOS Input Specifications (3.0V < VDD < 3.6V; 0C < T < 70C) Symbol Vil Vih Lil Iih Iil Iih VtVt+ Vh Parameter Low level input voltage High level input voltage Low level input current High level input current Input pull-up current Input pull-down current Schmitt negative threshold Schmitt positive threshold Schmitt hysteresis Min 0.7*VDD -27 35 0.2*VDD 0.8 Max 0.3*VDD -1 1 -75 112 0.8*VDD Unit V V A A A A V V V Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 8 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER TTL Input Specifications (3.0V < VDD < 3.6V; 0C < T < 70C) Symbol Vil Vih Lil Iih Iil Iih VtVt+ Vh Parameter Low level input voltage High level input voltage Low level input current High level input current Input pull-up current Input pull-down current Schmitt negative threshold Schmitt positive threshold Schmitt hysteresis Min 2 -27 35 0.7 0.4 Max 0.8 -1 1 -75 112 2.1 Unit V V A A A A V V V Output Operating Specifications (3.0V Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 9 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER AC Characteristics PCI Clock: Timing Diagram Thigh 2.0 V 5.0 V Clock 0.8 V Tlow Tr Tf 0.475 * vdd clamp 3.3 V Clock 0.325 * vdd clamp Tcycle PCI Clock Specification Timing Characteristics Symbol Tcycle Thigh Tlow Tr Tf Parameter Cycle time pci_clk high time pci_clk low time pci_clk slew rate pci_clk slew rate Min 30 11 11 1 1 Max 50 4 4 Unit ns ns ns V/ns V/ns Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 10 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER PCI Reset: Timing Diagram pci_clk pci_rst 10 pci_clk cycles Internal Reset 33 pci_clk cycles Timing Characteristics Symbol Trst Parameter pci_rst pulse width Min 10 * Tcycle Max Not applicable Conditions pci_clk active Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 11 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER PCI Other Signals: Timing Diagram clk Tval (max) Tval (min) Vtest* output Ton Toff input Tsu Th Note: Vtest is 1.5 V in a 5.0 V signaling environment and is 0.4 * vdd_clamp in a 3.3 V signaling environment. Timing Characteristics Symbol Tval Ton Toff Tsu Th Parameter clk-to-signal valid delay Float-to-active delay from clk Active -to-float delay from clk Input signal valid setup time before clk Input signal hold time from clk Min 2 2 7 0 Max 11 28 Unit ns ns ns ns ns Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 12 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER MII/SYM Port Timing Waveforms: Transmit: Timing Diagram Tcc Tcr Tch mii_sym_tclk Trv mii_sym_txd[3:0] Trh mii_sym_txen Tcf Tcl Timing Characteristics Symbol Tcc Tch Tcl Tcr Tcf Trv Trh * Definition mii_sym_tclk cycle time (50 ppm) mii_sym_tclk high time mii_sym_tclk low time mii_sym_tclk rise time mii_sym_tclk fall time mii_ tclk rise to mii_txen valid time mii_sym_tclk rise to mii_sym_txd valid time mii_txen hold after mii_tclk rise time or Min* 14t 14t 5 Typ* 40t 8 8 Max* 26t 26t 20 Units ns ns ns ns ns ns ns t = 1 for 100 Mbps operation and t = 10 for 10 Mbps operation. Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 13 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Receive: Timing Diagram Tcc Tcr Tch mii_sym_rclk Tts mii_sym_rxd[3:0] Tth Tcf Tcl mii_dv Timing Characteristics Symbol Tcc Tch Tcl Tcr Tcf Tts Definition mii_sym_rclk cycle time (50 ppm) mii_sym_rclk high time mii_sym_rclk low time mii_sym_rclk rise time mii_sym_rclk fall time mii_sym_rxd setup (both rise and fall) to mii_sym_rclk rise time or mii_dv setup (both rise and fall) to mii_rclk rise time mii_sym_rxd hold (both rise and fall) after mii_sym_rclk rise time or mii_dv hold (both rise and fall) after mii_rclk rise time. Min* 14t 14t 8 Typ* 40t 8 8 Max* 26t 26t Unit ns ns ns ns ns ns Tth 10 - - ns * t = 1 for 100 Mbps operation and t = 10 for 10 Mbps operation. Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 14 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Receive Error: Timing Diagram mii_rclk Tts sd Tth Timing Characteristics Symbol Tts Tth Definition mii_err setup (both rise and fall) to mii_rclk rise time mii_err hold (both rise and fall) after mii_rclk rise time. Min 10 10 Max 26t Units ns ns Collision and Carrier Sense: Timing Diagram mii_clsn mii_crs Tclh Timing Characteristics Symbol Tclh Definition Mii_crs, mii_clsn high time Min 20 Max Units ns Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 15 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Serial Port Timing Waveforms: Transmit: Timing Diagram Ttcf Ttcl srl_tclk Ttcc Ttdp srl_txd[3:0] Ttep srl_txen Tteh Ttdh Ttcr Ttch Timing Characteristics Symbol Ttcl Ttch Ttcr Ttcf Ttdp Ttdh Ttep Tteh Definition srl_tclk low time srl_tclk high time srl_tclk rise time srl_tclk fall time srl_tclk fall time to srl_txd valid srl_txd hold after srl_tclk fall time srl_tclk fall time to srl_txen valid srl_txen hold after srl_tclk fall time Min 45 45 5 5 Max 55 55 8 8 26 26 units ns ns ns ns ns ns ns ns Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 16 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Receive: Timing Diagram Start of Packet srl_rclk Trds Trcc Trdh Trcr Trcl Trch Trcf srl_rxd srl_rxen End of Packet srl_rclk srl_rxd Bit n-1 Bit n Treh Trel srl_rxen Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 17 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Timing Characteristics Symbol Trcc Trcl Trch Trcr Trcf Trds Trdh Trel treh Definition srl_rclk cycle time srl_rclk low time srl_rclk high time srl_rclk rise time srl_rclk fall time srl_rxd setup to srl_rclk fall time srl_rxd hold after srl_rclk fall time srl_rxen low time srl_rxen hold after srl_rclk rise time Min 85 38 38 10 5 120 10 Max 118 80 80 8 8 100 Units ns ns ns ns ns ns ns ns ns Collision: Timing Diagram Tclh srl_clsn Timing Characteristics Symbol Tclh Definition srl_clsn high time Min 20 Max Units ns Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 18 of 19 IA21140AF Preliminary Data Sheet PCI FAST ETHERNET LAN CONTROLLER Ordering Information Order Number IA21140AF-PQF144I Environment Industrial Package Type 144 Pin Plastic Quad Flat Package Cross Reference to Original Manufacturer Part Numbers: innovASIC Part Number DEC Part Number q q q IA21140AF-PQF144I 21140-AA 21140-AE 21140-AF Copyright (c) 2001 ENG210010110-00 innovASIC The End of ObsolescenceTM www.innovasic.com Customer Support: 1-888-824-4184 Page 19 of 19 |
Price & Availability of IA21140AF-PQF144I
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |